The Peavey PVi 8500 Powered Mixer has 8 input channels plus a 400 watt on board amplifier all in one!
The 8 input channels are either XLR or 1/4" giving you a variety of input options. The built in amplifier gives you 400 watts of peak power per channel at 8ohms. It will power your speakers, no additional amplifier needed. The mid-morph, digital effects and feedback eliminator provide you with a clear sound.
FLS Feedback Locating System Master Mute for channels 1-7 Foot-switchable effects defeat Combination XLR and 1/4" input jacks RCA, 1/8" Media input Selectable 9-Band Graphic EQ with FLS Selectable Main or Monitor dual power section RCA Record outputs LED Meter bridge Digital effects parameter control Power amp sub-sonic filtering On-board 24- bit digital effects with mute button Clip light and signal present indicator Kosmos-C Main line level 1/4" output Mid-Morph EQ DDT™ Speaker protection circuit 48 Volt Phantom Power Bluetooth® streaming audio
INPUT SENSITIVITY: Mic In to full power at the power amp. Master Volume Nom. Full Nominal -40 dBu -22 dBu Line In to full power at the power amp. Master Volume Nom. Full Nominal -10 dBu +8 dBu CHANNEL EQ: Shelving EQ Low EQ 80 Hz ±15 dB Mid-Morph Low 250 Hz ±15 dB High 4 kHz ±15 dB High EQ 12 kHz ±15 dB CLIP LED: Clip LEDs come on 3 dB before clipping. FREQUENCY RESPONSE: All controls nominal (detent) Mic to Main 20 Hz – 20 kHz +0, -1 dB Line to Main 20 Hz – 30 kHz +0, -1 dB Mic to Amp 50 Hz – 20 kHz +0, -3 dB Line to Amp 40 Hz – 20 kHz +0, -3 dB PHANTOM POWER: +48 VOLTS NOISE: Main = Main line output, 22 – 22 kHz filter Amp 1 = Amplifier output, loaded at 4 Ohms, through AP AUX-0025 switching amplifier filter All controls full down. Main <-95 dBu Amp 1 <-70 dBu Master Volume nominal Main <-88 dBu Amp 1 <-67 dBu THD: All controls nominal <0.01% @ main line output, -30 dBu in mic input Channel 1 <0.5% @ amp 1 @ 100 Watts into 4 Ohms All controls nominal <0.005% @ main line output, +4 dBu in line input Channel 1 <0.5% @ amp 1 @ 100 Watts into 4 Ohms MASTER EQ: 63Hz ±12 dB 125Hz ±12 dB 250Hz ±12 dB 500Hz ±12 dB 1kHz ±12 dB 2kHz ±12 dB 4kHz ±12 dB 8kHz ±12 dB 12kHz ±12 dB METER ARRAY: LIMIT -6 dB -12 dB -18 dB -24 dB -30 dB AMP LIMITER: Limits amplifier power just before clipping. The limiter holds the amp power without clipping and can be driven up to 18 dB past maximum output. AMPLIFIER OUT PUT POWER: 120VAC Both channels loaded at 8 ohms: 60 Watts RMS per ch 120 Watts Peak per ch Both channels loaded at 4 ohms: 100 Watts RMS per ch 200 Watts Peak per ch POWER REQUIREMENTS: Domestic: 120VAC 50/60Hz 74 Watts Nominal Export: 230VAC 50/60Hz 74 Watts Nominal