10" Heavy-duty woofer
Ultra-reliable fan-cooled power amps with DDT
Patented Quadratic Throat Waveguide™ technology, 100 by 50 degree coverage
Asymmetrical horn aims the sound down to 10 degrees, at the audience, not over their heads
400 watts peak available power
Thru output is via an XLR and 1/4" TRS phone jack
Durable plastic injection-molded trapezoidal enclosure
Full coverage heavy-duty perforated steel grilles, with powder coat finish
Pole mount molded-in for 1 3/8" diameter poles
RX™ 10N compression driver, with 1" diaphragm
Top and bottom flying point inserts
Input is via a combo female XLR and 1/4" TRS phone jack with balanced input
Two-way bi-amped sound reinforcement enclosure
Extra angled section on right side allows floor monitor use
Usable Low Frequency Limit (-10 Db Point Anechoic): 54 Hz
Nominal Sensitivity (1w @1m, Swept Sine Input In Anechoic Environment): 96 dB (average)
Maximum Sound Pressure Level (1 Meter): 122 dB SPL peak with music
Radiation Angle Measured At -6 Db Point Of Polar Response: Nominal: 100 degrees horizontal X 60 degrees vertical (Axis of the vertical main polar lobe is angled down 10 degrees, resulting in the angular pattern with respect to straight ahead being +20, -40 degrees)
Transducer Complement: Heavy-duty 10" woofer with 2-3/8" voice coil & 50 oz. magnet, RX™10N 1" titanium diaphragm dynamic compression driver with Neo magnet
Box Tuning Frequency: 75 Hz
Electroacoustic Crossover Frequency: 3,100 Hz
Crossover Type: Internal Electronic two-way crossover with driver EQ, level matching, bass boost and subsonic filtering.
Crossover Slopes: 24 dB/octave (4th order) low pass, 24dB/octave (fourth order) high pass, both with staggered poles and driver EQ.
Input Connections: One combo female XLR /1/4" phone jack providing balanced line-level operation from the 1/4" jack section, and high-output dynamic microphone operation from the XLR section.
Output Connections: One male XLR and one 1/4" phone jack. he Thru jacks are intended for the use of linking multiple PVXp 10 ‘s in a line or to provide a feed to a powered subwoofer, or other electronics that needs to receive a full range version of the input signal.
Enclosure Materials & Finish: Black ABS plastic with textured surface, black powder-coated perforated grille. Also available in white.
Mounting Provisions: Unit has two sets of two widely spaced M8 inserts, one pair on the top, and one pair on the bottom.
Additional mounting points are a set of four M8 inserts on the top and a set of four on the bottom, which use the Peavey VersaMount 70+ mounting bracket.
Four rubber feet provide vibration free floor or stage use, and a molded-in stand mounting cup is on the bottom.
Internal Power Amplifiers (@120 VAC line): Total of 400 watts peak available power Woofer - 300 watts peak available power
Continuous Power: 150 watts @ less than 1% distortion Tweeter - 100 watts peak available power
Continuous Power: 50 watts @ less than 1% distortion.
Electronic Input Impedance (Nominal): Line: 2.2 k ohms balanced (1/4"), 10 k ohms unbalanced 1/4" Mic: 2.2 k ohms balanced (XLR) No phantom power available.
Input Sensitivity for Full Output (Level full CW): 1/4" TRS Phone jack – 0.70 V RMS, XLR jack – 0.12 V RMS
Infrasonic Filter Protection: 36 dB/octave roll-off
Nominal Amplifier Frequency Response: +0, -3 dB from 20 Hz to 20 kHz
Hum and Noise: Greater than 90 dB below rated power
DDT™ Dynamic Range: Greater than 15 dB
THD and IM: Typically less than 0.5 %
Damping Factor: Greater than 100 @ 1000 Hz, 8 Ohms
Power Requirements of Peavey PVXp 10 System: Nominal 370 Watts, 100-120 VAC 50-60 Hz